本文针对一台在线运行的 H3C S5560S-28P-SI 交换机进行完整配置解析,运行环境为 Comware 7.1.070 Release 6328P03。文章按设备概况→全局参数→VLAN→DHCP→QoS→ACL→接口→路由/NTP→AAA→安全建议的顺序组织,并对每一段配置给出作用说明与潜在风险提示,便于网络运维人员对照检查。
一、设备概况
- 设备型号:H3C S5560S-28P-SI(1U 三层交换机,24×GE + 4 SFP 端口)
- 软件版本:Comware 7.1.070 Release 6328P03
- 运行时长:1 周 4 天 1 小时 25 分钟(最近一次重启原因:User reboot)
- 管理 IP:Vlan-interface100
192.168.100.254/24 - 默认路由出口:
0.0.0.0/0 → 192.168.100.100(上层网关/防火墙) - NTP 源:
time.windows.com(公网单源)
凭据说明:本文涉及
local-user admin与line aux 0的密码 hash 均已替换为<REDACTED>,不展示任何明文或可还原密文。
二、系统基础与全局参数
sysname 中S5560 # 设备名,含中文字符(GBK 编码)
clock timezone Beijing add 08:00:00 # 时区 = 北京 (+08:00)
clock protocol ntp # 时钟源协议 = NTP
telnet server enable # ⚠️ 开启 Telnet 明文登录(端口 23)
irf mac-address persistent timer # IRF 堆叠 MAC 表项持久化定时器
irf auto-update enable # IRF 自动升级(单台不生效,预留给堆叠)
undo irf link-delay # 关闭 IRF 链路延迟检测
irf member 1 priority 1 # IRF member 1 优先级 = 1(单台占位)
ip unreachables enable # 启用 ICMP Destination Unreachable
ip ttl-expires enable # 启用 ICMP Time Exceeded
dhcp enable # 全局开启 DHCP 功能
dhcp snooping enable # 全局开启 DHCP Snooping
dns proxy enable # 开启 DNS 代理
dns server 202.102.192.20 202.102.199.20
lldp global enable # 全局开启 LLDP
password-recovery enable # ⚠️ 允许 console 口重置密码
配置项解析
| 配置行 | 作用 | 备注/风险 |
|---|---|---|
sysname 中S5560 |
设备标识,出现在 prompt | 终端编码不一致会乱码,建议 SSH/console 用 UTF-8 |
clock timezone … +08:00 |
影响所有时间戳显示 | 客户端时区不对要手动同步 |
telnet server enable |
启动端口 23 | 明文协议,强烈建议改 SSH 或限定源 IP |
irf … |
出厂默认 IRF 配置 | 单台无意义,真要堆叠需补 irf-port |
undo irf link-delay |
关闭 IRF 链路延迟检测 | 单台无所谓;堆叠场景别 undo |
ip unreachables enable / ttl-expires enable |
配合 traceroute / PMTU 发现 | 暴露设备 IP 给扫描器 |
dhcp snooping enable |
全局开关,需 VLAN 上单独启用 | 见下文接口段 |
password-recovery enable |
console 口可重置密码 | 安全风险:机房设备建议关闭 |
三、VLAN 数据库
vlan 1 # 默认 VLAN,未做业务
vlan 2 to 10 # 业务 VLAN 2-10 批量创建
vlan 20
vlan 30
vlan 40
vlan 50
vlan 60
vlan 70
vlan 80
vlan 90
vlan 100 # 管理 VLAN + 防火墙接入
vlan 200 # 预留
- VLAN 1 仍存在:默认所有未配置端口在 VLAN 1,建议把 access 端口
port default vlan X改到具体业务 VLAN。 - VLAN 200 没有接口引用,纯预留,可用于监控 / IoT 扩展。
四、DHCP 服务器配置
全局 dhcp enable 已在第一节开启,下面 10 个 ip-pool 共享同一 DHCP server 实例。
4.1 地址池总览
| Pool 名 | 网关 | 分配范围 | DNS | 静态绑定数 |
|---|---|---|---|---|
| vlan1 | 192.168.1.1 | .100–.200 | 202.102.199.20, 192.168.1.1 | 1 |
| vlan2 | 192.168.2.1 | .100–.200 | 202.102.199.20, 192.168.2.1 | 3 |
| vlan3 | 192.168.3.1 | .100–.200 | 202.102.199.20, 192.168.3.1 | 1 |
| vlan4 | 192.168.4.1 | .100–.200 | 192.168.4.1, 202.102.199.20 | 0 |
| vlan5 | 192.168.5.1 | .99–.200 | 192.168.5.1, 202.102.199.20 | 1 |
| vlan6 | 192.168.6.1 | .100–.200 | 192.168.6.1, 202.102.199.20 | 1 |
| vlan7 | 192.168.7.1 | .3–.200 | 192.168.7.1, 202.102.199.20 | 8 |
| vlan8 | 192.168.8.1 | .98–.200 | 192.168.8.1, 202.102.199.20 | 4 |
| vlan9 | 192.168.9.1 | .98–.200 | 192.168.9.1, 202.102.199.20 | 11 |
| vlan10 | 192.168.10.1 | .100–.200 | 192.168.10.1 | 0 |
4.2 关键 DHCP 段(节选 vlan7)
dhcp server ip-pool vlan7
gateway-list 192.168.7.1
network 192.168.7.0 mask 255.255.255.0
address range 192.168.7.3 192.168.7.200
dns-list 192.168.7.1 202.102.199.20
forbidden-ip 192.168.7.1
static-bind ip-address 192.168.7.3 mask 255.255.255.0 hardware-address 000c-29df-ff88
static-bind ip-address 192.168.7.4 mask 255.255.255.0 hardware-address 244b-fee9-7912
static-bind ip-address 192.168.7.6 mask 255.255.255.0 hardware-address 000c-29c9-e105
static-bind ip-address 192.168.7.7 mask 255.255.255.0 hardware-address 000c-2979-efd1
static-bind ip-address 192.168.7.11 mask 255.255.255.0 hardware-address 000c-29c1-e094
static-bind ip-address 192.168.7.98 mask 255.255.255.0 hardware-address 6c92-bfc4-7ae4
static-bind ip-address 192.168.7.100 mask 255.255.255.0 hardware-address 6c92-bfc4-7ae2
static-bind ip-address 192.168.7.136 mask 255.255.255.0 hardware-address 000c-29ae-578a
4.3 DHCP 段观察要点
- 大量 MAC 以
000c-29xx/08cc-81xx开头:这是 VMware 虚拟机默认 OUI,说明 vlan7/8/9 的 static-bind 大概率是虚拟机 IP 固定需求。若虚拟化平台迁移,这些绑定将成为孤儿。 vlan2漏写network:其它 pool 都写了network 192.168.x.0 mask 255.255.255.0,vlan2 漏写,配置不严谨。vlan10只有dns-list 192.168.10.1:把网关当 DNS,若该 VLAN 没有 DNS 代理,用户解析会失败。forbidden-ip只列 .1:通常用forbidden-ip 192.168.x.1 192.168.x.100避免网关+保留起始地址段冲突。- 缺租期设置:使用 H3C 默认值(一般 1 天)。如需调整,加
lease day X hour Y。
五、QoS(流量分类 / 行为 / 策略)
traffic classifier hao0564 operator and
if-match acl 3000
traffic classifier icmp operator and
traffic behavior hao_http
car cir 1024 cbs 64000 ebs 0 green pass red discard yellow pass
traffic behavior icm
traffic behavior icmp
qos policy hao_http
classifier hao0564 behavior hao_http
qos policy ahha
classifier icmp behavior icm
behavior hao_http用 CAR 限速到 1024 kbps:cir 1024承诺信息速率 1 Mbps,ebs 0不允许超额突发,绿/黄包放行、红包丢弃。qos policy ahha把classifier icmp绑到behavior icm(注意 behavior 名是icm而非icmp,可能是历史笔误),且该策略没有任何接口引用。- 真正下发需要
qos apply policy,见下文 GE1/0/1 接口段。
六、ACL(访问控制列表)
acl advanced 3000
rule 10 deny tcp source 192.168.7.4 0 destination-port eq 443
acl advanced 3001
rule 0 deny ip source 192.168.9.99 0 destination 192.168.5.100 0
| ACL | 动作 | 含义 |
|---|---|---|
| 3000 rule 10 | deny tcp src 192.168.7.4 dst-port 443 |
封 vlan7 上 .4 的 HTTPS 出站(仅 443,不影响 http 80) |
| 3001 rule 0 | deny ip src 192.168.9.99 dst 192.168.5.100 |
禁止 vlan9 .99 访问 vlan5 .100(任意协议/端口) |
⚠️ 两段 ACL 都没有
packet-filter引用,只是分类器里被 QoS 引用,没有真正做包过滤。如需真正生效,需在 Vlan-interface 上加packet-filter 3000 inbound/packet-filter 3001 inbound。
七、接口配置
7.1 Bridge-Aggregation(链路聚合)
interface Bridge-Aggregation1
description 核心交换机G1/0/23-G1/0/24
port link-type trunk
port trunk permit vlan all
link-aggregation mode dynamic
interface Bridge-Aggregation2
description 客户端防火墙Guest接GE1/0/3-GE1/0/4
port access vlan 100
link-aggregation mode dynamic
- BAG1:上联核心交换机,trunk 所有 VLAN。
- BAG2:上联防火墙,access vlan 100(管理 + Guest)。
- 均为
mode dynamic(LACP),对端也需 LACP 才能协商成功。
7.2 VLAN 接口(SVI)
interface Vlan-interface1 ip address 192.168.1.1 255.255.255.0
interface Vlan-interface2 ip address 192.168.2.1 255.255.255.128 # /25
interface Vlan-interface3 ip address 192.168.3.1 255.255.255.0
interface Vlan-interface4 ip address 192.168.4.1 255.255.255.0
interface Vlan-interface5 ip address 192.168.5.1 255.255.255.0
interface Vlan-interface6 ip address 192.168.6.1 255.255.255.0
interface Vlan-interface7 ip address 192.168.7.1 255.255.255.0
dhcp server apply ip-pool vlan7
interface Vlan-interface8 ip address 192.168.8.1 255.255.255.0
dhcp server apply ip-pool vlan8
interface Vlan-interface9 ip address 192.168.9.1 255.255.255.0
dhcp server apply ip-pool vlan9
interface Vlan-interface10 ip address 192.168.10.1 255.255.255.0
interface Vlan-interface20 ip address 192.168.20.1 255.255.255.0
interface Vlan-interface30 ip address 192.168.30.1 255.255.255.0
interface Vlan-interface100 ip address 192.168.100.254 255.255.255.0
7.3 GigabitEthernet 物理端口(关键口)
# 上联 / 防火墙主用口
interface GigabitEthernet1/0/1
port link-mode bridge
description 客户端防火墙g1/0/1口
port access vlan 100
qos apply policy hao_http inbound
dhcp snooping trust
dhcp snooping binding record
# 防火墙聚合(备用链路)
interface GigabitEthernet1/0/21
port link-mode bridge
description 客户端防火墙Guest接GE1/0/3-GE1/0/4
port access vlan 100
port link-aggregation group 2
interface GigabitEthernet1/0/22
port link-mode bridge
description 客户端防火墙Guest接GE1/0/3-GE1/0/4
port access vlan 100
port link-aggregation group 2
# 核心聚合(上联)
interface GigabitEthernet1/0/23
port link-mode bridge
port link-type trunk
port trunk permit vlan all
port link-aggregation group 1
interface GigabitEthernet1/0/24
port link-mode bridge
port link-type trunk
port trunk permit vlan all
port link-aggregation group 1
# 其他 GE 口(默认在 VLAN 1)
interface GigabitEthernet1/0/2 ~ GigabitEthernet1/0/28
port link-mode bridge
7.4 接口段观察
- GE1/0/1 限速 1Mbps inbound:防火墙主用口。CAR 限速,建议确认是哪个网络(Guest 还是内网)。
- GE1/0/21、22 加入 BAG2 但 BAG2 没有 dhcp snooping trust:从 BAG2 收到的 DHCP 报文会被当成客户端报文丢弃,是潜在 DHCP 故障点。
- GE1/0/2–28(除聚合口)所有端口都在 VLAN 1:安全风险——任何插线设备进入 VLAN 1,建议
port default vlan X改到具体业务 VLAN。 - 未启用 STP 边缘端口:access 口默认跑 STP 收敛,DHCP 获取 IP 有 30s 延迟,建议
stp edged-port enable+stp bpdu-protection。 - 未启用 port-security / 802.1X:纯 DHCP snooping 不阻断非法 MAC。
八、路由与 NTP
ip route-static 0.0.0.0 0 192.168.100.100 # 默认路由
ntp-service enable
ntp-service unicast-server time.windows.com # 唯一 NTP 源
- 默认路由单出口:上层挂掉所有 VLAN 断网。可加
ip route-static ... preference X做浮动路由或 VRRP。 - NTP 单源公网域名:依赖 DNS 解析,没配认证。建议加内网 NTP 同步服务器做主源,公网做备。
九、AAA 与用户管理
line class aux
user-role network-admin
line class vty
user-role network-operator
line aux 0
authentication-mode password
user-role network-admin
set authentication password hash <REDACTED>
line vty 0 63
authentication-mode scheme
user-role network-admin
user-role network-operator
radius scheme system
user-name-format without-domain
domain system
domain default enable system
local-user admin class manage
password hash <REDACTED>
service-type ftp telnet http https terminal
authorization-attribute work-directory flash:/
authorization-attribute user-role network-admin
authorization-attribute user-role network-operator
ip http enable
ip https enable
9.1 AAA 段观察
- VTY 用
authentication-mode scheme但 RADIUS 方案system没配 server:当前 RADIUS 认证必失败,实际靠 AAA fallback 走本地local-user admin。生产环境需补radius scheme system primary server <ip>。 - aux 口和 telnet 口是两套独立密码 hash:管理混乱,建议统一走 AAA 路径,
undo set authentication password。 service-type ftp:本地用户不需 FTP 能力,建议删除降低攻击面。authorization-attribute user-role network-admin + network-operator:同时具备 admin 和 operator 权限。- 未启用
password-control:建议password-control enable+ 复杂度 / 轮换 / 历史策略。 - 无 VTY ACL:
line vty 0 63没配acl 2000 inbound,任何 IP 都能 telnet 进来。
十、安全与管理面总结
| 项 | 当前状态 | 建议 |
|---|---|---|
| Telnet 服务 | 开启(明文) | undo telnet server enable,启用 ssh server enable |
| HTTP 服务 | 开启(明文) | undo ip http enable,只用 HTTPS |
| VTY ACL | 无 | 加 line vty 0 63 的 acl 2000 inbound |
| 密码策略 | 未启用 | password-control enable + 长度 / 复杂度 |
| RADIUS | 方案存在无 server | 补 primary server 或移除该段 |
| SSH server | 未开启 | ssh server enable(首选) |
| 端口安全 | 仅 DHCP snooping | access 口加 port-security 或 802.1X |
| STP 边缘端口 | 默认非边缘 | access 口 stp edged-port enable |
| BPDU guard | 无 | stp bpdu-protection |
| DHCP snooping trust | 仅 G1/0/1 | BAG2 也加 trust,VLAN 启用 snooping |
| 风暴抑制 | 未配 | access 口 storm-constrain |
| ACL | 仅 2 条,未生效 | 加 packet-filter 真正过滤 |
| 配置保存 | 未观察到 save |
save 把运行配置写入 flash |
十一、依赖与时序关系(总览)
[外网] → [192.168.100.100 网关]
↓
[BAG1 / G1/0/23-24 trunk]
↓
[本设备 S5560] ← 管理 VLAN 100 (.254)
↓ ↓ ↓
vlan 2-10, 20/30 vlan 100 静态默认路由
SVI .1 业务网关 BAG2 / G1/0/21-22
DHCP server (本机) ↓
[防火墙客户端网段]
G1/0/1 限速 1Mbps
G1/0/1 = dhcp snooping trust
DHCP Snooping:
trust 端口: G1/0/1(防火墙主用口)
⚠️ BAG2 端口(G1/0/21/22)trust 状态未设
本文仅作只读分析,未对设备做任何写操作。所有配置数据均来自通过 telnet/应用密码抓取的 display current-configuration 输出,密码 hash 已脱敏。如需针对 ACL、SSH、AAA、DHCP snooping 等具体模块的改造方案,欢迎评论区留言讨论。
H3C交换机IRF及BFD MAD检测配置实验:https://www.hao0564.com/5803.html
